.. include:: ./../../../macros.txt
.. include:: ./../../../units.txt


.. |local_bms_master_version| replace:: ``v1.1.1``
.. |local_bms_master_identifier_short| replace:: |ti-tms570|-based |bms-master|
.. |local_bms_master_identifier_full| replace:: |local_bms_master_identifier_short| |local_bms_master_version|

.. _TI_TMS570_BASED_BMS_MASTER_V1_1_1:

|local_bms_master_identifier_full|
==================================

.. note::

   The changelog for this release is found at
   :numref:`CHANGELOG_FOR_THE_TI_TMS570_BASED_BMS_MASTER_V1_1_1`.

.. important::

   |bms-master| release :ref:`TI_TMS570_BASED_BMS_MASTER_V1_2_2` is designed
   and prepared for a CAN based bootloader for remote firmware update.
   Follow the instructions to establish bootloader compatibility on older
   hardware.

.. toctree::
    :maxdepth: 1

    ./ti-tms570lc4357-v1.1.1/ti-tms570lc4357-v1.1.1_block_diagram.rst
    ./ti-tms570lc4357-v1.1.1/ti-tms570lc4357-v1.1.1_functional_description.rst
    ./ti-tms570lc4357-v1.1.1/ti-tms570lc4357-v1.1.1_pinout.rst

The following specifications must be met to ensure a safe and optimal work with
the |bms-master| hardware.

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Removing the Pull-up Resistor for the PHY
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

In |bms-master| v1.2.3 and below, the PHY is enabled by default,
which can cause issues when connecting the Ethernet cable.
To avoid this, the pull-up resistors enabling the PHY should be removed.
The image below shows the location of the pull-up resistors on the PCB.

.. image:: ./ti-tms570lc4357-v1.1.1/img/ti-tms570lc4357-v1.1.1_pull_up_resistors.png
   :alt: Pull-up resistors for the PHY
   :name: ti-tms570lc4357-v1.1.1_pull_up_resistors


^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Bootloader Compatibility on |bms-master| prior to v1.2.2
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

In |bms-master| release :ref:`TI_TMS570_BASED_BMS_MASTER_V1_2_2`, the CAN1
Enable and Standby signals have been wired directly to the MCU, instead of
using |I2C| based port expander.
Therefore, on |bms-master| prior to v1.2.2 the CAN1 transceiver would not be
enabled during bootloader operation, lacking the feature of firmware update
capability.

By de-soldering populated 10kOhm pull-down resistors R6320_2 and R6321_2, the
CAN1 transceiver will be enabled by default and is available during
bootloader operation.

Details are shown in
:numref:`resistors-for-foxbms_v1.1.1._bootloader_compatibility`.

.. figure:: ti-tms570lc4357-v1.1.1/img/foxbms_v1.1.1._bootloader_compatibility.png
   :alt: Resistors R6320_2 and R6321_2 to be removed for compatibility with bootloader
   :name: resistors-for-foxbms_v1.1.1._bootloader_compatibility
   :width: 100 %

   Resistors R6320_2 and R6321_2 to be removed for compatibility with bootloader

^^^^^^^^^^^^^^^^^^
Electrical Ratings
^^^^^^^^^^^^^^^^^^

==================================================  =======     =======     =======     ====
Description                                         Minimum     Typical     Maximum     Unit
==================================================  =======     =======     =======     ====
Supply Voltage Clamp 30 (VSUP_30)                   9           12          36          V DC
Supply Voltage Clamp 30C (VSUP_30C)                 9           12          36          V DC
Contactor Continuous Current                        --          --          1.8         A
Contactor Feedback Supply Voltage                   --          VSUP_30     --          V
Interlock Circuit Sink Current                      --          10          --          mA
Idle Supply Current at 12V DC for VSUP_30           --          215         --          mA
Idle Supply Current at 24V DC for VSUP_30           --          160         --          mA
==================================================  =======     =======     =======     ====

.. note::
   The maximum supply voltage is limited by the SBC.
   It is validated for limited duration for higher voltages.
   For further information see the `SBC documentation`_.

.. _SBC documentation: https://www.nxp.com/part/MC33FS8530A0ES

^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Mechanical Dimensions (|bms-master| PCB only)
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^

==================================================  =======     =======
Description                                         Value       Unit
==================================================  =======     =======
Width                                               120         mm
Length                                              200         mm
Height                                              13          mm
Weight                                              129         g
==================================================  =======     =======