1. System Introduction
2. Conditions that lead to a transition to ERROR state
Logging after 20th event for errors connected related to the contactor feedback. This value is chosen to be so large because of the time delay between the request for a state and the actual physical response. It is caused by the SPI transaction to the SPS module, the rise time of the control signal and the actual opening/closing of the contactor. Only then can the feedback be read correctly, which also takes some additional time depending on the selected feedback source.
Diagnosis Entry |
Response time in ms |
Delay time in ms |
|---|---|---|
DIAG_ID_INTERLOCK_FEEDBACK |
to be added |
to be added |
DIAG_ID_SUPPLY_VOLTAGE_CLAMP_30C_LOST |
to be added |
to be added |
DIAG_ID_CELL_VOLTAGE_OVERVOLTAGE_MSL |
to be added |
to be added |
DIAG_ID_CELL_VOLTAGE_UNDERVOLTAGE_MSL |
to be added |
to be added |
DIAG_ID_TEMP_OVERTEMPERATURE_CHARGE_MSL |
to be added |
to be added |
DIAG_ID_TEMP_OVERTEMPERATURE_DISCHARGE_MSL |
to be added |
to be added |
DIAG_ID_TEMP_UNDERTEMPERATURE_CHARGE_MSL |
to be added |
to be added |
DIAG_ID_TEMP_UNDERTEMPERATURE_DISCHARGE_MSL |
to be added |
to be added |
DIAG_ID_OVERCURRENT_CHARGE_CELL_MSL |
to be added |
to be added |
DIAG_ID_OVERCURRENT_DISCHARGE_CELL_MSL |
to be added |
to be added |
DIAG_ID_STRING_OVERCURRENT_CHARGE_MSL |
to be added |
to be added |
DIAG_ID_STRING_OVERCURRENT_DISCHARGE_MSL |
to be added |
to be added |
DIAG_ID_PACK_OVERCURRENT_DISCHARGE_MSL |
to be added |
to be added |
DIAG_ID_PACK_OVERCURRENT_CHARGE_MSL |
to be added |
to be added |
DIAG_ID_CURRENT_ON_OPEN_STRING |
to be added |
to be added |
DIAG_ID_AFE_SPI |
to be added |
to be added |
DIAG_ID_AFE_COMMUNICATION_INTEGRITY |
to be added |
to be added |
DIAG_ID_AFE_MUX |
to be added |
to be added |
DIAG_ID_AFE_CONFIG |
to be added |
to be added |
DIAG_ID_CAN_TIMING |
to be added |
to be added |
DIAG_ID_CURRENT_SENSOR_CC_RESPONDING |
to be added |
to be added |
DIAG_ID_CURRENT_SENSOR_EC_RESPONDING |
to be added |
to be added |
DIAG_ID_CURRENT_SENSOR_RESPONDING |
to be added |
to be added |
DIAG_ID_SBC_RSTB_ERROR |
to be added |
to be added |
DIAG_ID_STRING_MINUS_CONTACTOR_FEEDBACK |
to be added |
to be added |
DIAG_ID_PRECHARGE_CONTACTOR_FEEDBACK |
to be added |
to be added |
DIAG_ID_DEEP_DISCHARGE_DETECTED |
to be added |
to be added |
DIAG_ID_CURRENT_MEASUREMENT_TIMEOUT |
to be added |
to be added |
DIAG_ID_CURRENT_MEASUREMENT_ERROR |
to be added |
to be added |
DIAG_ID_CURRENT_SENSOR_V1_MEASUREMENT_TIMEOUT |
to be added |
to be added |
DIAG_ID_CURRENT_SENSOR_V2_MEASUREMENT_TIMEOUT |
to be added |
to be added |
DIAG_ID_CURRENT_SENSOR_V3_MEASUREMENT_TIMEOUT |
to be added |
to be added |
DIAG_ID_CURRENT_SENSOR_POWER_MEASUREMENT_TIMEOUT |
to be added |
to be added |
DIAG_ID_POWER_MEASUREMENT_ERROR |
to be added |
to be added |
DIAG_ID_ALERT_MODE |
to be added |
to be added |
