4.29.7. NXP MC33775A

4.29.7.1. Description

The MC33775A monitoring IC can monitor 4 to 14 cells, with +/- 5V voltage. It has 8 GPIOs. GPIO 4 and 5 can be used for I2C communication. GPIO 1 can be used as alarm line.

The communication with the MC33775A can be made directly via SPI or through a differential line. This type of communication is called TPL. To translate SPI communication to TPL communication, a bridge IC is used, called MC33664.

In SPI mode, only 1 MC33775A can communicate with the MCU. In TPL mode, the MCU can communicate with up to 62 MC33775A in daisy-chain.

4.29.7.2. Daisy-chain

4.29.7.2.1. Wake-up

A device wakes up when there is any communication on the TPL bus. In addition, there is a WAKE-UP command that can be sent. When an enumerated device receives a WAKE-UP command, it automatically transmits an additional WAKE-UP message to the next device. When an unenumerated device receives a WAKE-UP command, it automatically sends two additional WAKE-UP messages to the next devices.

As a consequence, sending two WAKE-UP commands (separated by the wake-up delay) allows waking up the entire daisy-chain. In the case of enumerated devices, it works as follows:

  • The MCU sends the first WAKE-UP command (WU0)

  • IC0 is woken up by WU0

  • The MCU sends a second WAKE-UP command WU1

  • IC0 gets WU1 and forwards it to IC1, as IC0 is enumerated

  • IC1 is woken up by WU1

  • IC0 automatically transmits a second WAKE-UP command (WU2)

  • IC1 gets WU2 and forwards it to IC2, as IC1 is enumerated

  • IC2 is woken up by WU2

  • IC2 automatically transmits a third WAKE-UP command (WU3)

  • The process goes on until the whole daisy-chain is woken-up

For an unenumerated daisy-chain, it works as follows:

  • The MCU sends the first WAKE-UP command (WU0)

  • IC0 is woken up by WU0

  • The MCU sends a second WAKE-UP command WU1

  • IC0 gets WU1 checks it

  • IC0 sends WU1_1 to IC1

  • IC1 wakes up

  • IC0 sends WU1_2 to IC1

  • IC1 checks WU1_2

  • IC1 sends WU2_1 to IC2

  • IC2 wakes up

  • IC1 sends WU2_2 to IC2

  • IC2 checks WU2_2

  • IC2 sends WU3_1 to IC3

  • IC3 wakes up

  • IC1 sends WU3_2 to IC3

  • IC3 checks WU3_2

  • The process goes on until the whole daisy-chain is woken-up

4.29.7.2.2. Addressing of slaves

In daisy-chain mode, every MC33775A has its own address. The MC33775A starts unenumerated, which means its address is 0 and it does not forward messages.

To enumerate an MC33775A, a write command must be sent to the daisy-chain, to write the address of the device in the SYS_COM_CFG register. For the first MC33775A, 1 must be written in the address field: due to the use of 0 to represent an unenumerated device, the addresses start at 1. The bus forwarding must be enabled, too, by writing 1 to bit 9. After this procedure, the first MC33775A is then enumerated.

Once a MC33775A is enumerated, it forwards all messages in both directions. For the second MC33775A, the configuration message with 2 in the address field must be sent to the daisy-chain. As this address in the configuration message does not match the address of the first MC33775A, it is ignored and simply forwarded. The second MC33775A then receives the configuration message and becomes enumerated. The MCU must then repeat the enumeration procedure for each unenumerated MC33775A in the daisy-chain, by sending the configuration message for address setup and forward enabling.

When all the ICs in the daisy-chain are enumerated and forwarding is enabled, the communication between the MCU and the daisy-chain works as follows:

  • when the MCU sends a message to the daisy-chain, it is received by IC(0). IC(0) forwards it to IC(1). IC(1) forwards it to IC(2) and soon until the last IC in the daisy-chain receives the message. As each message contains the address of the IC that is addressed by the MCU, this addressed IC knows it has to interpret the message and not only forward it.

  • When IC(n) sends a message to the MCU (e.g., response to a voltage measurement request), it sends it to IC(n-1). IC(n-1) forwards it to IC(n-2) and so on until IC(0) forwards it to the MCU

This means that when communicating with the daisy-chain, the MCU does not see a shift register. It sees single devices to which it sends messages and which answer.

4.29.7.2.3. TPL

TPL is the name of the differential communication protocol used by the MC33775A ICs to communicate in daisy-chain. A bridge IC called MC33664 is used to make the translation between SPI and TPL, so that the MCU only sees SPI communications. The MC33664 has one important specificity: it uses two SPI interfaces to communicate with the MCU, one Tx SPI and one Rx SPI. The SPI interfaces are configured as follows:

  • The Tx SPI is used by the MCU as a master to send messages to the daisy-chain

  • The Rx SPI is used by the MCU as a slave to receive answers from the daisy-chain

4.29.7.3. Message format

There are 4 types of message:

  • WAKE-UP/NOP

  • READ register from MC33775A

  • WRITE register to MC33775A

  • RESPONSE of MC33775A to READ message

A RESPONSE message is received after a READ command was issued. In TPL mode, there is no response to WRITE message.

The following fields compose messages and are common to all types of messages:

  • CMD: command type, chooses one of the four command types described above.

  • MADD: indicates upstream of downstream direction of message. Must be set to 0 by the MCU when sending messages to the daisy-chain.

  • CADD: daisy-chain address. Cannot be 0.

  • DEVADD: device address. 0 is for enumerated devices. For enumerated devices, the MCU sets this value to the address of the device it wants to communicate with and in RESPONSE messages, contains the address of the device that responded.

  • MSGCNT: message counter, is incremented for each response message sent by a MC33775A IC. Is ignored in other messages. The counter is reset when the device goes to sleep.

  • DATLEN: number of register addressed, can be 1 to 4. With one message, up to 4 consecutive register can be read from or written to. If DATLEN is higher then the length of the provided data, the communication is discarded.

  • REGADD: address of the first addressed register.

The next fields are related to data and depend on the type of messages. For WRITE and RESPONSE messages, DATA contains the data to write for WRITE or the data sent by the device for RESPONSE.

For READ messages:

  • PAD: padding. If set to 1, the response message always correspond to a RESPLEN of 4. If RESPLEN < 4 was used, the remaining values are padded with zeros.

  • RESPLEN: number of messages to be transferred in one RESPONSE frame, can be 1 to 4. RESPLEN greater than number of registers to transfer?

  • NUMREG: total number of register requested. If NUMREG is not a multiple of RESPLEN, the device sends in the last message only the remaining registers. If PAD is set to 0, the length of the last message is adapted. If PAD is set to 1, the remaining values are padded with zeros.

The last field is the CRC value.

4.29.7.4. Writing values to registers

The WRITE message must be used. In the message, the address of the device, the address of the register and the data to write must simply be supplied.

The following data must be written.

First the message head:

  • 0x10 in CMD

  • 0 in MADD

  • CADD value

  • device address in DEVADD. Care must be taken, the first device in the daisy-chain has the address 1.

  • As MSGCNT is not used, it can be set to 0.

Then the data segment starts, first with the data head:

  • Message length in DATLEN. A length of 1 corresponds to 0 for DATLEN.

  • Address of first consecutive register in REGADD.

Then the data of the data segment:

  • Data to write.

Finally the CRC:

  • CRC value computed over the whole message.

In TPL mode, the daisy-chain does not respond to WRITE commands.

4.29.7.5. Reading values from registers

4.29.7.5.1. Issuing a read command

First, a READ command must be used. In the message, the address of the device and the address of the first consecutive register to read must e supplied.

The following data must be written.

First the message head:

  • 0x01 in CMD

  • 0 in MADD

  • CADD value

  • device address in DEVADD. Care must be taken, the first device in the daisy-chain has the address 1.

  • As MSGCNT is not used, it can be set to 0.

Then the data segment starts, first with the data head:

  • Message length in DATLEN. A length of 1 corresponds to 0 for DATLEN.

  • Address of first consecutive register in REGADD.

Then the data read configuration part of the data segment:

  • Five bits must be written with 0.

  • PAD must be set to 0 or 1.

  • Response length in RESPLEN. A length of 1 corresponds to 0 in RESPLEN.

  • Number of registers to read in NUMREG.

Finally the CRC:

  • CRC value computed over the whole message.

4.29.7.5.2. Response from the daisy-chain

After a READ message was sent to a device in the daisy-chain, via the Tx SPI, the device answers via the Rx SPI.

Different checks in a RESPONSE frame can be made to determine if the READ command was performed successfully:

  • the length of the received message must be greater than zero.

  • the device address in RESPONSE messages must match the device address used in the WRITE message.

  • the register address in each received RESPONSE message must correspond to the register address written in the WRITE command. Care must be taken that one WRITE message can lead to several RESPONSE messages, so the value of the first register written in the WRITE COMMAND has to be incremented for each RESPONSE message received.

  • the message counter MSGCNT can be checked, it is incremented at each response message. It is reset when the device goes to sleep.

  • If the register address of a RESPONSE frame contains 0x3FFF, this means there was an access error.

  • The CMD field in a respond message must be set to 0x11.

In addition, the FEH_COM_FLT_STAT register (Communication fault status register, address 0x423) can be read. It signals communication errors that happened and contains a communication error counter.

4.29.7.6. Voltage measurement

The MC33775A can measure the following values:

  • 14 cell voltages

  • 4 + 4 voltages on analog inputs that can also be used as GPIOs

  • voltage of the battery module

  • diagnostic measurements like voltage references and internal IC temperature

The analog inputs can be used to measure temperature by using NTCs in a voltage dividers, supplied by the output VAUX.

The MC33775A has two independent measurements chains, primary and secondary.

Primary can measure:

  • the 14 cell voltages

  • the 4 first analog inputs (AIN0 to AIN3)

  • internal primary IC temperature

  • various voltage references, not the same as secondary

Secondary can measure:

  • the 14 cell voltages

  • the 4 last analog inputs (AIN4 to AIN7)

  • internal secondary IC temperature

  • various voltage references, not the same as primary

The first step is to activate measurements. The IC then continuously measures. When one of the 4 modes described above is started, the measurements are captured. At least 16 measurements are necessary for the IC to give valid values.

4.29.7.6.1. Measurement types

4 different types of measurement are available:

  • synchronous

  • application-driven

  • periodic

  • fast VB

4.29.7.6.1.1. Synchronous

In this mode, the cell voltages are measured synchronously between primary and secondary. Only the inputs common to primary and secondary (cell voltages) are taken into account, the other inputs (analog inputs, module voltage, internal temperature, voltage references) not.

4.29.7.6.1.2. Application-driven

In this mode, the application decides when the capture starts. The measurements are taken into account after the IC receives a capture command via setting bits in the appropriate register. All sources can be measured. Results are available as soon as at least 16 measurements have been taken into account. This is signaled by a bit in the appropriate register.

A new capture can be initiated when at least 16 values have been taken into account. If more than 65535 or less than 16 measurements have been captured, the results are set to invalid.

4.29.7.6.1.3. Periodic

The number of measurements to use is defined in the appropriate register. Once this mode is started, the results are available every time the number of measurements captured corresponding to the configured period has been made. The availability of the results of a period are signaled by a bit in the appropriate register.

4.29.7.6.1.4. Fast VB

Measurements are made on the secondary line. The results are available after 24 measurements have been captured.

4.29.7.6.1.5. Measurement possibilities for primary and secondary

The following table sums up which inputs can be measured by primary and secondary and with which method.

Measurement sources and measurement types

Synchronous

Application

Periodic

Fast VB

Primary

VC0 to VC13

X

X

X

AIN0 to AIN3

X

X

Module voltage

X

X

Primary refs

X

Secondary

VB0 to VB13

X

X

AIN4 to AIN7

X

X

Secondary refs, Current

X

4.29.7.7. Procedure to perform voltage measurements

Writing to the ALLM register is equivalent to writing simultaneously to the corresponding

PRMM (primary) and SECM (secondary register).

4.29.7.7.1. Measurement unit activation

First, the measurement units must be activated:

  • Enable cell measurement channels by writing ones to the VCBCxEN fields in the ALLM_VCVB_CFG register (address 0x1408).

    • ALLM_VCVB_CFG ← 0x3FFF

  • Enable AIN0 to AIN 3 and module voltage channels by writing ones to the AINx fields in the PRMM_AIN_CFG register (address 0x1809).

    • PRMM_AIN_CFG ← 0x1F

  • Enable AIN4 to AIN 7 channels by writing ones to the AINx fields in the SECM_AIN_CFG register (address 0x1C09).

    • PRMM_AIN_CFG ← 0x0F

  • Enable the measurements units simultaneously by setting bit 0 to 1 in the ALLM_CFG register (address 0x1400).

    • ALLM_CFG register ← 0x01

Once the measurement units have been activated, measurement captures can be started.

4.29.7.7.2. Application-driven measurements

  • Enable capture by setting the bits 0 to 9 corresponding the the different channels (cell inputs, analog inputs, module voltage) to 1 (corresponding to a value of 0x1FF) in the ALLM_APP_CTRL register (address 0x1401). Also write 0x1F to bits 14:10 to disable open load detection for secondary. Writing a number between 0 to 13 would activate open load detection for the corresponding cell measurement input.

    • ALLM_APP_CTRL ← (0x1F << 10) | 0x3FF

  • In the PRMM_MEAS_STAT register (address 0x183E), the status of the primary measurements can be checked. If at least 16 measurements have been captured, the corresponding bit for each of the 6 measurement possibilities is set to 1:

    • cell inputs VC0 to VC13 - bit 0

    • analog inputs AIN0 to AIN3 - bit 1 to bit 4

    • module voltage - bit 5

  • In the PRMM_APP_VC_CNT register (address 0x183F), the number of captured values for the cell input measurements can be read. Starting from address 0x1840, the results of the measurements can be read, with one value per register, in the following order:

    • cell inputs VC0 to VC13

    • module voltage.

    • analog inputs AIN0 to AIN3

  • Starting from address 0x1C4F, the results of the secondary measurements can be read, with one value per register, in the order analog inputs AIN4 to AIN7.

4.29.7.7.3. Periodic measurements

  • Set the number of measurements used for each period by writing the corresponding value to the ALLM_PER_CTRL register (address 0x1402) at bits 0 to 8 (PERLEN). The number must lie between 16 and 511.

    • ALLM_PER_CTRL ← 0x10 for 16 measurements

  • In the PRMM_MEAS_STAT register (address 0x183E), the status of the periodic measurements can be checked. If new periodic data is ready for readout, bit 8 (PERRDY) is set to 1.

  • The number of the cycle in which the results have been created can be read in the PRMM_PER_NUM register (address 0x185F). Starting from address 0x1860, the results of the measurements can be read, with one value per register, in the following order:

    • cell inputs VC0 to VC13

    • module voltage.

    • analog inputs AIN0 to AIN3

  • Starting from address 0x1C6E, the results of the secondary measurements can be read, with one value per register, in the order analog inputs AIN4 to AIN7.

4.29.7.7.4. Synchronous measurements

  • Enable capture by setting the bit 0 (SYNCCYC) to 1 in the ALLM_SYNC_CTRL register (address 0x1403). Also write 0x1F to bits 14:10 to disable open load detection for secondary. Writing a number between 0 to 13 would activate open load detection for the corresponding cell measurement input.

    • ALLM_SYNC_CTRL ← (0x1F << 10) | 0x01

  • In the PRMM_MEAS_STAT register (address 0x183E), the status of the synchronous measurements can be checked. If synchronous data is ready for readout, bit 9 (SYNCRDY) is set to 1.

  • The number of the cycle in which the results have been created can be read in the PRMM_SYNC_NUM register (address 0x187F). Starting from address 0x1880, the results of the measurements can be read, with one value per register, in the order cell inputs VC0 to VC13

4.29.7.8. Balancing

The following figure sums up the different switches for balancing.

Balancing switches

Fig. 4.11 Balancing switches

Balancing can be controlled by different means:

  • Global timer: all balancing stops when it reaches 0

  • Channel timer: the corresponding channel stops balancing when the timer reaches 0

  • Global undervoltage: all balancing stops when one cell reaches this value

  • Channel undervoltage: the corresponding channel stops balancing when its voltage reaches the limit

  • Pre-balancing timer: if set to no zero, balancing only starts when it has reached zero

  • PWM: modulates balancing for each channels

  • Temperature-controlled balancing: two temperature limits are defined, measured with analog inputs. When the high limit is reached, all balancing stops. It starts again when the low limit is reached.

There are three prerequisites for balancing to start:

  • In the BAL_GLOB_TO_TMR register (address 0x1001), the global timer TOTIME must be set to a non-zero value.

  • In the BAL_PRE_TMR register (address 0x1003), the pre-balancing timer must be set to 0 to balance immediately

  • In the BAL_GLOB_CFG register (address 0x1000), the global balancing enable flag BALEN must be set to 1.

    • BAL_GLOB_TO_TMR ← 0xYYYY with YYYY>0 and high enough

    • Set all individual channels to values high enough

    • BAL_PRE_TMR ← 0x00

    • BAL_GLOB ← 0x01

Once this is done, setting bits CHEN0-CHEN13 to 1 in the BAL_CH_CFG register (address 0x1002) activates the corresponding balancing channel.

4.29.7.9. I2C

The MC33775A can act as a I2C master, by using GPIO4 and GPIO5 as SCL and SDA. The I2C configuration is made in the I2C_CFG register (address 0xC00). Bit 0 enables the I2C interface. Bit 1 select the clock rate (100 or 400 kHz)

Register I2C_DATA0 (address 0xC04) to I2C_DATA6 (address 0xC0A) contains the data transmitted or received, depending on the form of the transmission.

The transmission is started by writing to the I2C_CTRL register (address 0xC01):

  • bits 3:0 (START) control how many bytes are transmitted after the START condition, including device address

  • bit 4 (STOP) determines if a stop condition is sent after the last transmitted bytes

  • bits 11:8 (RDAFTER) determines after how many bytes the master switches to read

Data to be sent must be written in the registers I2C_DATA0 to I2C_DATA6 before the transmission starts. Data received must be read in the registers I2C_DATA0 to I2C_DATA6 after the transmission.

In the I2C_STAT register (address 0xC02), the status of the transmission can be polled. Bit 1 (ACTIVE) states that a transmission is ongoing. TO check is the ongoing transmission is finished, the register must be polled until the value 0 is read for the ACTIVE bit.

4.29.7.10. GPIOs

The GPIOs are driven by two configuration registers and two control registers.

The GPIO_CFG0 register (address 0x800) is the first control register. Bits 7:0 (INPEN0 to INPEN7) enable the inputs for the pins. Bits 15:8 (OUTEN0 to OUTEN7) enable the outputs for the pins.

The GPIO_CFG1 register (address 0x801) is the second control register. Bits 7:0 (ODEN0 to ODEN7) allows enabling the open-drain for each pin.

The GPIO_OUT register (address 0x802) is the first control register. Bits 7:0 (OUT0 to OUT7) set the output levels of the pins.

The GPIO_IN register (address 0x803) is the second control register. Reading bits 7:0 (IN0 to IN7) gives the level of the GPIO pins. Reading bits 15:8 (HIGHDET0 to HIGHDET7) indicate if a high level was present on the pin since the last READ command.